Qureos Mentor

Drake-Williams Steel, Inc.

<div>$27- $35+
Primary Purpose of this Position:
To maintain or repair DWS fabrication equipment, material handling equipment, buildings, facilities, and processes. Work on &ldquo;projects&rdquo; that improve the DWS processes. Make building and facility repairs.
Essential Job Functions:<ul><li>
PM machines based on PM procedures to help ensure machines run properly and efficiently.</li><li>
Troubleshoot mechanical/electrical issues on equipment that is down.</li><li>
Contact vendors for supplies and recommendations.</li><li>
Input information into the Mega Mation tracking system.
</li><li>Strategically visualize and communicate project plans and supplies needed.
</li><li>Identify steel shapes, sizes, and mill tolerances for projects.</li><li>
Operate overhead cranes, forklifts, jib cranes, gantry cranes, conveyors, machines, and transfers in order to PM or repair them.</li><li>
Any other duties assigned by management (example- plow snow, sand lot, and grounds maintenance.</li><li>
Attend all meetings as required by management.</li><li>
Consistently and reliably works scheduled hours at assigned locations.</li></ul>
FLSA Status: Non-Exempt
Reporting Relationships:<ul><li>
Maintenance Manager</li><li>
Support Services Director</li></ul>
Knowledge, Skills and Abilities:
<ul><li>Ability to read, write, and perform higher arithmetic computations involving addition, subtraction, multiplication, and division of whole numbers, decimals and fractions.</li><li>
Ability to understand and carry out semi-complicated verbal and written instructions.</li><li>
Ability to effectively communicate with vendors, co-workers, supervisors and managers.</li><li>
Ability to work under periodic supervision focused on the progress of work and setting priorities for job completion.</li><li>
Skill in using tape measure, or other measuring devices.</li><li>
Ability to pass a Drake-Williams Steel, Inc. administered test that covers shop drawing interpretation, fractional number calculations, basic geometry, etc.</li><li>
Ability to interpret shop drawings for projects.</li><li>
Ability to possess pride in own workmanship, demonstrate attention to detail, and work safely.</li><li>
Ability to operate forklifts and overhead cranes in a safe and proper manner. Use and understand industry and Drake-Williams Steel adopted hand signals used for crane operations.</li><li>
Perform minor/major mechanical tasks on machines.</li><li>
Ability to multi-task.</li></ul>
Physical Demands:<ul><li>
Stand OCCASIONALLY to FREQUENTLY over the course of the 8 to 12 hour work shift depending on needs.</li><li>
Walk OCCASIONALLY to FREQUENTLY over the course of the 8 to 12 hour work shift.
</li><li>Sit OCCASIONALLY during break, lunch periods, and to input data.
</li><li>Lift weights up to 25 pounds FREQUENTLY from floor to waist, which includes the various tools, chains, valves, and various components during the 8 to 12 hour work shift.</li><li>
Lift weights up to 100 pounds OCCASIONALLY from floor to waist, which includes the various motors and components during installation or removal during the 8 to 12 hour work shift.
</li><li>Carry 100 pound weight noted above distances up to 10 feet. Lighter weights may be carried up to several hundred feet depending on job location.
</li><li>Climb OCCASIONALLY to FREQUENTLY up and down steps, ladders, onto material, or onto conveyors depending on job location.
</li><li>Balance OCCASIONALLY while working on machinery and climbing into and out of the manlift.</li><li>
Bend OCCASIONALLY depending on task location while removing tools, components, etc.</li><li>
Stoop or crouch OCCASIONALLY while performing the regular job duties. The position will be held continuously for a few seconds to 15 minutes, depending upon the job.</li><li>
Kneel in the commission of job duties OCCASIONALLY, depending upon the job.
</li><li>Crawl OCCASIONALLY up to 15 feet to access tools, materials, etc.</li><li>
Reach forward FREQUENTLY to perform job duties or to retrieve tools. The employee will OCCASIONALLY be required to reach to full forward extension.</li><li>
Reach overhead OCCASIONALLY to FREQUENTLY to work on forklifts, cranes, machines, building, etc.
</li><li>Push and pull material OCCASIONALLY to FREQUENTLY with force of up to 50 pounds. The distance may be from a few feet to several hundred feet while pushing parts on the worktable or pushing a paint pump.
</li><li>Pull hand over hand OCCASIONALLY to FREQUENTLY to pull chain through material. Force varies up to 70 pounds.</li><li>
Gross finger dexterity skills required to operate the various tools and equipment utilized in the course of standard job duties.
</li><li>Fine finger dexterity skills required to operate the various tools and equipment utilized in the course of standard job duties.</li></ul>
<ul><li><ul><li>Non-Material Handling Demands</li></ul></li><li>
Employee is expected to work 40 hours a week. However, hours including overtime and weekends may be required based on Drake-Williams Steel&rsquo;s needs.</li><li>
Hear sufficiently to be aware of safety issues</li><li>
Visual ability to read and interpret schematics, manuals, etc. Safety glasses are required in the shop area.</li><li>
Exposure to heat, cold, wet and humid conditions inside and/or outside of the facilities OCCASIONALLY.
</li><li>Exposure to fumes, odors and dusts in the shop area OCCASIONALLY.
</li><li>Exposure to solvents, greases, oils, and coolants OCCASIONALLY.</li><li>
Wear all required Personal Protective Equipment. PPE includes steel-toe safety shoes, hearing protection, safety glasses, gloves, and hard hats.</li><li>
Work at heights that may range up to 40 feet.</li></ul>
Tools Required:
Pencil, Tape Measure, Markers, Chainsaw, Grab Hooks, Pry-Bar, Ladders, Remote Control, Wrenches, Hammers, Drills, Chains, Electrical Test Equipment, etc.
Machines Utilized:
Overhead Crane, Jib Crane, Gantry Crane, Transfers, Fabrication Process Equipment, Computers, Tractors, Mobile Yard Crane, Snow Plow/Sander, Manlift, and Forklifts.
Experience and Education Required:<ul><li>
High School degree or equivalent.</li><li>
Minimum of six months of experience in a manufacturing environment.</li></ul>
Please visit our Employee Benefits page for more information!</div>

Maintenance Tech DS

Join Drake-Williams Steel, Inc. and explore 1   exciting career opportunities. They're hiring for various roles with options for remote or on-site work. Apply today and become part of their innovative team.

Drake-Williams Steel, Inc.

ABOUT_COMPANY

Maintenance Tech DS